Electrochemical performance of a nano SnO2-modified LiNi1/3Co1/3Mn1/3O2 cathode material

The nano SnO₂-modified LiNi_1/3Co_1/3Mn_1/3O₂ was successfully prepared by a carrier transfer method. The pristine and modified samples were characterized with various techniques such as XRD, SEM, XPS and EDS. The results showed that the SnO₂ particles did not enter the crystal structure of LiNi1/3Co1/ 3Mn1/3O₂, many nano SnO₂ particles were uniformly covered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ and the modified thin layer could inhibit the dissolution of transition metal oxides. The electrochemical tests indicated that the existence of nano SnO₂ could improve the discharge capacity and rate capability owing to the decreased interfacial polarization. The cycling stability was remarkably improved at room temperature and 55 ℃. The XRD patterns of the fresh NCM electrode and after 50 cycles proved that the structural change of NCM was not so effective on the capacity fade.     

Preparation,characterization and hydrodesulfurization performances of Co-Ni2P/SBA-15 catalysts

A series of Co-Ni2P/SBA-15 catalysts with various Co contents, Ni2P contents and P/Ni molar ratios were prepared by impregnating nickel nitrate, diammonium hydrogen phosphate, and then cobalt nitrate into SBA-15 support followed by temperature-programmed reduction in a H2 flow. The catalyst structure was characterized by X-ray diffraction(XRD), high resolution-transmission electron microscopy(HR-TEM)and N2adsorption-desorption techniques and their catalytic performance of the hydrodesulfurization(HDS) of dibenzothiophene(DBT) was evaluated. The effects of Co contents, Ni2 P contents and P/Ni molar ratios on the catalyst structure and HDS of DBT over the Co-Ni2P/SBA-15 catalyst were investigated. The results indicated that the mesoporous structure was mainly maintained and the nickel phosphides were well dispersed in all of the characterized catalysts. The 4Co-25Ni2P/SBA-15(P/Ni = 0.8) catalyst with the Co and Ni2 P contents of 4 wt% and25 wt%, respectively, and the P/Ni molar ratio of 0.8 showed the highest catalytic performance for HDS of DBT. Under the reaction conditions of 380?C and 3.0 MPa, the DBT conversion can reach 99.62%. The HDS of DBT proceeded mainly via the direct desulfurization(DDS)pathway with biphenyl(BP) as the dominant product on all of the catalysts and the BP selectivity was slightly enhanced after the introduction of Co promoters.     

超声波促进手性双酰基氧化膦的合成

以L-薄荷醇为原料,经3步反应制备得到中间体薄荷基二氯化膦.该中间体首先通过与超声波辐射制备的微米级钠粒反应形成薄荷基膦二钠盐,然后依次经过偶联及氧化反应合成了目标产物(-)-双(薄荷基甲酰基)薄荷基氧化膦(BMMPO),并经过1 H NMR、13 C NMR、31P NMR和元素分析进行了表征.     

HPLC–ICP–MS法测定农田土壤中甲基汞和乙基汞

采用HPLC反相C18柱分离、ICP–MS检测,建立了农田土壤中甲基汞和乙基汞的分析方法。以0.5mol/L的硝酸溶液为浸提剂,超声波提取1 h,在优化的仪器条件下测定,甲基汞和乙基汞的质量浓度在0.1~50ng/m L范围内与谱线强度呈良好线性关系(r≥0.999),检出限分别为0.1,0.2 ng/m L;加标回收率分别为89.26%~94.26%,76.88%~79.27%;相对标准偏差分别为1.67%~2.38%,2.58%~3.84%(n=5)。该方法样品前处理简单、重现性好、检出限低、准确度高,适合于农田土壤中甲基汞和乙基汞的同时测定。     

基于色谱–光谱联用和斜投影法分析丹皮酚含量

将色谱–光谱仪联用(HPLC–UV)法与斜投影法结合,建立了丹皮酚含量快速分析方法。通过色谱–光谱联用采集丹皮酚结晶母液的紫外多波长光谱三维数据,构建不含丹皮酚的背景数据库以及丹皮酚光谱数据库,基于斜投影法步骤测定了批量样本中丹皮酚含量。结果表明:该方法计算结果和高效液相色谱分析结果接近,相对误差小于5.0%。测定结果的相对标准偏差为0.4%~1.0%(n=5),回收率为98.8%~101.3%。该方法快速、准确,操作简单,可为丹皮酚结晶产品及各种制剂质量控制提供可行方案。     

喹啉黄中各组分的定性及定量研究

利用高效液相色谱(HPLC)对喹啉黄各组分进行分离并定量,通过液相色谱–串联质谱(LC–MS/MS)对各组分进行定性。以0.01 mol/L乙酸铵溶液和甲醇为流动相进行梯度洗脱,利用Agilent XDB–C18色谱柱对喹啉黄各组分进行分离,峰面积归一化法定量。质谱采用电喷雾负离子(ESI–)模式电离,多反应监测(MRM)模式检测,对喹啉黄各组分进行定性。结果表明,喹啉黄主要成分为喹啉黄一钠盐和喹啉黄二钠盐,分别各有两种同分异构体,各组分质量浓度在5.0~100.0μg/m L范围内与峰面积呈良好的线性关系。加标回收率为98.2%~99.1%,测定结果的相对标准偏差为0.90%~1.58%(n=6)。该方法具有良好的精密度和准确度,可用于喹啉黄中各组分的测定。     

罗丹明B分子印迹固相萃取小柱的研制及应用

研制一种对罗丹明B具有特异性识别性能的分子印迹固相萃取小柱。用沉淀聚合法制备罗丹明B分子印迹聚合物,通过静态平衡吸附实验及固相萃取实验表征其性能,并对市售辣椒样品中的罗丹明B进行测量。罗丹明B模板聚合物的吸附能力明显优于空白聚合物;印迹固相萃取小柱对罗丹明B标准溶液(0.05 mmol/L)一次性萃取率为98.24%,实际样品测量的回收率为90.0%~95.0%,测定结果的相对标准偏差为0.9%~1.7%(n=3)。罗丹明B分子印迹固相萃取小柱选择性好、萃取率高,可应用于食品、化妆品检测等相关领域。     

石墨烯非共价功能化及其应用

石墨烯的湿法化学修饰,主要包括共价及非共价两种,是目前广泛采用的宏量功能化策略,亦是有效避免其团聚而充分发挥其优异纳米性能的重要修饰方法。非共价功能化因可同时保持原有及引入物质的物化性质,并可充分发挥协同作用,近年来已受到比共价修饰更多的研究关注,并已在生物科学与技术、可持续能源储存及转化、医疗和复合材料等诸多领域得到了广泛应用。本文综述了以应用为导向的石墨烯非共价功能化的构建策略,期望文中涉及的湿法组装策略能为进一步构建性能提升的新材料提供参考。     

新型低共熔溶剂的制备、表征及物性研究

以氯化1-丁基-3-甲基咪唑鎓([Bmim]Cl)和二元羧酸为原料,由不同摩尔比混合制备了一类新型低共熔溶剂,采用红外光谱对[Bmim]Cl和二元羧酸之间的作用进行了分析。分别测定了其粘度、电导率、密度、折射率等物理性质,并研究了温度、二元羧酸结构和摩尔比对这些物理性质的影响。结果表明,新型低共熔溶剂的粘度随温度的升高而降低,电导率随温度的升高而增加。温度对两者的影响可以采用VTF方程进行精确地拟合。新型低共熔溶剂的密度随温度的升高而呈线性下降。对新型低共熔溶剂的过量摩尔体积进行计算的结果表明,过量摩尔体积均为正值,二元羧酸对过量摩尔体积的贡献远大于[BMIM]Cl,而结构特性的贡献多于物理作用。折射率和密度随二元羧酸碳数的变化趋势基本相似。     

氧化环境和比例对改性Hummers法制备GO的影响

以鳞片石墨(GR)为原料,采用改性Hummers法液相氧化方法制备氧化石墨,通过超声剥离的方法剥离出片状的氧化石墨烯(GO),探讨了H₂SO₄环境与H₂SO₄+H₃PO₄混酸环境和KMnO₄与GR的比例对GO制备的影响。采用FTIR、UV、TG、XRD、SEM和XPS等分析手段对制备的GO进行分析。结果表明：GO外貌是呈褶皱片状,在片层上主要有C=O、C-OH、-COOH和C-O-C等官能团,以共价键形式存在石墨层间;通过TG与XPS数据分析表明在H₂SO₄ H₃PO₄混酸环境下制备的GO含氧官能团较多,并且(KMnO₄)与鳞片石墨的最佳比例是1:4。